openlp/documentation/manual/source/dualmonitors.rst
2011-03-11 05:48:48 -05:00

183 lines
6.3 KiB
ReStructuredText

==================
Dual Monitor Setup
==================
The first step in getting OpenLP working on your system is to setup your
computer properly for dual monitors. This is not very difficult, but the steps
will vary depending on operating system.
Most modern computers have the ability for dual monitors. To be certain,
check your computer's documentation. A typical desktop computer capable of dual
monitors will have two of, or a combination of the two, connectors below.
**VGA**
.. image:: pics/vga.png
**DVI**
.. image:: pics/dvi.png
A laptop computer setup only varies slightly. Generally you will need only one
of the outputs pictured above since your laptop screen serves as one of the
monitors. Sometimes with older laptops a key stroke generally involving the
:kbd:`Fn` key and another key is required to enable the second monitor on
laptops.
Some computers also incorporate the use of :abbr:`S-Video (Separate Video)` or
:abbr:`HDMI (High-Definition Multimedia Interface)` connections.
A typical OpenLP setup consist of your normal single monitor, with your
projector hooked up to your computer as the second monitor. With the option of
extending your desktop across the second monitor, or your operating system's
equivalent.
Microsoft Windows
-----------------
Dual monitor setup is similar among all the currently supported Windows
releases (XP, Vista, Windows 7), but does vary slightly from one release to the
next.
Windows 7
^^^^^^^^^
Windows 7 has using a projector in mind. Simply connect your projector and
press :kbd:`Windows+P`.
The more traditional way is also fairly straight forward. Go to
:guilabel:`Control Panel` and click on :guilabel:`Display`. This will open up
the :guilabel:`Display` dialog. You may also bypass this step by a right click
on a blank area on your desktop and selecting :guilabel:`Resolution`.
.. image:: pics/winsevendisplay.png
Then click on the :guilabel:`Adjust resolution` link in the left pane. Enable
your projector and make sure that the selected value for :guilabel:`Multiple
displays` is :guilabel:`Extend these displays`.
.. image:: pics/winsevenresolution.png
Windows Vista
^^^^^^^^^^^^^
From :guilabel:`Control Panel` click on :guilabel:`Personalize`, or right click
a blank place on the desktop and click :guilabel:`Personalization`.
.. image:: pics/vistapersonalize.png
From the :guilabel:`Personalization` window click on :guilabel:`Display
Settings`. Click on the monitor that represents your projector and make sure
you have checked :guilabel:`Extend the desktop onto this monitor`.
.. image:: pics/vistadisplaysettings.png
Windows XP
^^^^^^^^^^
From :guilabel:`Control Panel` select :guilabel:`Display`, or right click on a
blank area of the desktop and select :guilabel:`Properties`. From the
:guilabel:`Display Properties` window click on the :guilabel:`Settings` tab.
Click on the monitor that represents your projector and make sure you have
checked :guilabel:`Extend my Windows desktop onto this monitor`.
.. image:: pics/xpdisplaysettings.png
Linux
-----
Due to the vast varieties of hardware, distributions, desktops, and drivers
this is not an exhaustive guide to dual monitor setup on Linux. This guide
assumes you have properly set up any proprietary drivers if needed. You
should seek out your distributions documentation if this general guide does not
work.
GNOME
^^^^^
This guide is for users of the GNOME desktop who do not use proprietary drivers.
From most distros go to :menuselection:`System --> Preferences --> Display
Settings (Monitors)`. Set up your projector with the correct resolution and make
sure that :guilabel:`Same image on all monitors` is **unchecked**.
.. image:: pics/gnome.png
KDE
^^^
This guide is for users of the KDE desktop who do not use proprietary drivers.
From most distros click the Kick Off menu and navigate to
:guilabel:`System Settings`
.. image:: pics/kdesystemsettings.png
Click on the display and monitor icon.
.. image:: pics/kdedisplay.png
From here you will need to set up your projector with the appropriate
resolution, and position. OpenLP works best projecting to the monitor on the
right.
Linux Systems Using nVidia Drivers
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
This guide is for users of the proprietary nVidia driver on Linux Distributions.
It is assumed that you have properly setup your drivers according to your
distribution's documentation, and you have a working ``xorg.conf`` file in
place.
If you wish to make the changes permanent in setting up your system for dual
monitors it will be necessary to modify your ``xorg.conf`` file. It is always a
good idea to make a backup of any critical file before making changes::
user@linux:~ $ sudo cp /etc/X11/xorg.conf /etc/X11/xorg.conf.old
Or for those using systems that use the root user instead of sudo, change to
root and enter::
root@linux: # cp /etc/X11/xorg.conf /etc/X11/xorg.conf.old
The exact location of the ``xorg.conf`` file can vary so check your
distribution's documentation.
If you want to make your changes permanent run nVidia settings from the
terminal::
user@linux:~ $ sudo nvidia-settings
Or, as root::
root@linux: # nividia-settings
If you do not want to write the changes to your ``xorg.conf`` file simply run
the nVidia Settings program (:command:`nvidia-settings`) from your desktop's
menu, usually in an administration or system menu, or from the terminal as a
normal user run::
user@linux:~ $ nvidia-settings
Once you have opened nVidia Settings, click on :guilabel:`X Server Display
Configuration`. Then select the monitor you are wanting to use as your second
monitor and click :guilabel:`Configure`.
.. image:: pics/nvlinux1.png
After clicking :guilabel:`Configure`, select :guilabel:`TwinView`. Then click
:guilabel:`OK`.
.. image:: pics/twinview.png
Click :guilabel:`Apply` and if you are happy with the way things look click
:guilabel:`Keep` to keep your new settings. Don't worry if all goes wrong the
settings will return back to the previous settings in 15 seconds without any
action. nVidia Settings should take care of selecting your optimum resolution
etc, but that can be changed as needed. When you are happy with everything click
on :guilabel:`Save to X Configuration File`.
.. image:: pics/xorgwrite.png
Click :guilabel:`Save` and you should be set. You may want to restart X or
your machine just to make sure all the settings carry over the next time you log
in.